Delaney KA2006 Bedienerhandbuch PDF herunterladen

INSTRUCTIONS FOR INSTALLATION

ONE SIDED DEADLOCK

B. Rotate turnpiece to locked

position

(bon extended).

Insert two oval head mounting

screws and tighten.

Insert and tighten two flat head wood

screws.

B Cen er strike plate over hole and mark

arouncl

out ide with pencil or scribe.

With

dl l el cut out jamb to a depth of

V 16"( 1.5mm) or until strike plate can

be installed lIush.

L03ale strike plate by m.uking end ot

bolt with marking crayon or lipstick.

Close door and operate bon back and

lorth several times to mark the jamb.

Locale the center of spot and drill a

1"(25m

m) hole a minimum of 1"(25mm)

deep.

( Lock will not function properly

hole

is not deep enough.)

Oeadbolt

Inside Tum Unit

INSTALL MOUNTING

-j

--~

.....

-"'

- '>--f>tate on Side Elf

Latch Facing Inside Of

Ooor.

A. Align torque blade of thumb

turn assembly with crank

in latch and press flush

against

doo r.

, 5

INSTALL STRIKE

IMPORTANT:Oo not hammer

on latch if bolt is extended.

O.For round lace deadbolt.

simply press lIush to door

edge. Bolt must be vertically

aligned with door edge as

indicated by arrow.

B.Chisel V8"(3mm) deep or until

face plato! of Oeadbolt is lIush

with door

edge.

B. Mark center hole on door lace

through guide on

terrotate.

ith3r 2-3/8" (60mm) or

2-3/4"(70mm) backsat. -

edge

door, drill a r(25mm)

diameter latch hole where previously

marked. Orill 41102mm) deep. Then

drill as was mark a 1

-51S

"(41mm)

hole making sure not to break through

to opposite

sid6. Orill just past the

r(25mm)

diarreter hole.

3. INSTALL LATCH

A. Insert latch into hole keeping

it parallel to face of door.

Mark outline and remove latch.

A. Fold and apply te

rT4l

late to

high

edge

of door bevel and

mark cen:er

door

edge

for

(25mm

) tc

hOle

indicated of terroiate at the

desired height from the

1I00r

C. Install deadbolt latch in

"up"

position into hole as shown

on latch. Insert and tighten

screws.

CAUTION:DO NOT DRILL

1·5/8

(41mm)

HOLE

THROUGH ENTIRE DOOR.

(READ INSTRUCTIONS

CAREFULLY)

Backset

2-3/8°(60mm)

MARK

FOR

1-318

(35mm)

THICK

DOOR

MARK

FOR

1-314" OR

(45mm)

THICK

DOOR

Fold here on door edge.

------------T-~Auno;---------------MINIMUM----

I DO NOT DRILL 1-5/8' DOOR THICKNESS

HOLE

THR

OUGH

THE M

ARK

CEN

TER

OF 1-3/8'(35mm)

ENTIRE

DOOR

. 1-5/8' (41mm)

I DRILL JUST

PAST

HOLE ON

DOOR

FACE

I THE

HOLE FOR

LATCH

-----/--<t

T~--

_----------+----+f.+-----...---------------

lSI

11..,

-----/--<t 1

Inhaltsverzeichnis

Seite 1 - -----/--<t

INSTRUCTIONS FOR INSTALLATIONONE SIDED DEADLOCKOFB. Rotate turnpiece to lockedposition(bon extended).Insert two oval head mountingscrews and tighten.I

Kommentare zu diesen Handbüchern

Keine Kommentare

Delaney KA2006 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Delaney KA2006 herunter. Delaney KA2006 Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Delaney KA2006